Certain McFarlane universal joints for single-engine Cessna aircraft may fail and should be immediately inspected and/or replaced. The good news is that McFarlane has offered to help defray replacement costs for owners with affected parts.

On Dec. 11, 2017, McFarlane issued Service Bulletin SB-9, Revision A. This service bulletin addresses concerns with a replacement universal joint (Part No. MC0411257) that fits several models of single-engine Cessna airplanes, from the Cessna 120 all the way through the Cessna 210. 

The service bulletin applies to certain lot numbers of the universal joint that were sold in 2015 and 2016. The affected “Job Order” numbers in the bulletin include JO41505, JO41997, JO43600 and JO45454. 

 

Purpose of a universal joint

A universal joint is typically used to connect two shafts that are not directly in line with one another. The universal joint is hinged so that it flexes in two different planes that are 90 degrees apart. Another way to put it is that a universal joint flexes both up-and-down and from side to side. 

The universal joint that is the subject of the service bulletin is a bendable connection between the control wheel shaft and the Y-shaped control yoke assembly under the instrument panel. There are two universal joints installed in each aircraft, one on the pilot side and one on the co-pilot side. 

A failure and subsequent separation of either universal joint would render the control wheel on the side with the failed joint inoperative. Either the pilot or co-pilot—depending on which side failed—would no longer have control of the ailerons or elevator.

The McFarlane universal joint is designed with two yokes that provide the attach points for connecting the control wheel shaft and control yoke shaft; a center pin and two half-pins that the yokes pivot around; and a center block used as a base for mounting the pins. 

A rivet is used to secure the pins and yokes to the block. If the rivet were to break apart and slide out, the entire mechanism could come apart.

 

 

Service Bulletin SB-9, Revision A

It’s important to remember that service bulletins are not Airworthiness Directives. Even if a manufacturer refers to a service bulletin as mandatory, a private aircraft owner is under no FAA mandate to comply with it. As a result, some owners and mechanics may disregard service bulletins as being not all that serious. This service bulletin should be taken seriously, however, because the consequences of a failure of the universal joint are dire. 

Compliance with the service bulletin is straightforward. The initial inspection should be done immediately.  

The first step is to inspect the part and identify the “JO” (lot) number stamped on the universal joint itself to see if one of the affected joints is installed. The lot number and part number may or may not be visible by simply inspecting the joint without removing it. 

Some universal joints have protective sleeves made of rubber hose sections that are slid over the joint. Universals with sleeves installed may require removal so the sleeve can be slid back far enough to inspect the part and lot numbers. There are only two bolts and nuts that connect the universal to the system, so removal doesn’t usually take too long. 

If the joint part and lot number falls within the range listed, the universal joint should be removed and inspected.

The service bulletin states that if a joint passes the initial inspection, it must be re-inspected at 25-hour intervals. The joint may be kept in service for the next 100 flight hours or for one year after the first inspection, whichever comes first. After either of these limits is reached, the joint must be replaced.

Affected parts should be replaced as soon as possible, even if they pass inspection. Completion of the service bulletin by replacing the parts will provide peace of mind and negate the need for further inspections.  

 

 

Inspection of affected universal joints

Once removed, the inspection process for each universal is fairly simple. Each universal yoke should rotate freely in its range of motion. 

The yokes are designed to pivot around the center pin and half-pins. The pins should remain in a stationary position in the block and they should not move as the yokes are pivoted around them. If the yokes are bound or not freely pivoting, the universal joint must be replaced.

Service Bulletin SB-9 includes illustrations for marking the pins and yokes with a straight line using a permanent marker with the yokes held straight. Once the mark is made, bend each yoke; the line should appear broken as the yoke is pivoted around the pin. 

If the line remains unbroken as the yokes are bent, the pin is moving along with the yoke and the universal joint cannot remain in service.  

The center pin is easier to inspect than the two half pins that are installed under the rivet head and tail. Note that the illustration in Revision A of the service bulletin under the paragraph for the half pin inspection (See top image on Page 31) is actually an illustration of the center pin inspection. The concept is the same, however: the yokes should rotate around the pins while the pins themselves remain stationary. The rivet should be tight with no end-play or looseness. 

 

 

 

(Re)installation

Assuming that the joint passes inspection and it hasn’t exceeded the time limits specified in the service bulletin, it can be reinstalled. Any joint which fails the inspection should be replaced with a new MC0411257 joint. 

As noted above, one could argue that any joint from the affected lots (even one which passes inspection) should be replaced as soon as possible, as McFarlane is currently offering to assist in defraying the cost of replacement (see “Replacement parts” Page 35). 

Before installing new McFarlane universal joints that didn’t come directly from McFarlane Aviation (for example, parts from a maintenance shop’s spare stock), double-check to ensure they are not accidentally from one of the bad lots.

Some Cessna parts manuals specify that a protective sleeve be installed over the pivoting mechanism of the universal joint. The sleeve is made of a short section of reinforced hose and is listed under its own part number in the parts manual. This sleeve provides a small measure of support for the joint, in addition to protecting it from grit or debris that could cause it to bind. 

McFarlane specifies in SB-9, Revision A that it now requires the protective sleeve on all MC0411257 universal joint installations, whether or not the aircraft parts manual specifically lists it. 

The Cessna service manual recommends using general-purpose oil (MIL-L-7870) as a lubricant for the universal joints. McFarlane forbids the use of any type of penetrating oil like WD-40 on its universals. Most spray-can lubricants have penetrating qualities. General-purpose oil is heavier than penetrating oil and is usually applied with an old-fashioned hand-pump squirt can or with a brush. 

After installation, the control wheel should be moved from stop to stop in all directions to be sure that it moves freely with no binding. Replacement parts

Speaking as both a mechanic and a pilot, it’s commendable that McFarlane is currently offering both a parts and labor credit toward the replacement of affected universal joints. (As of early April, McFarlane has the parts in stock, ready to ship. —Ed.)

The service bulletin states “McFarlane Aviation, Inc. will issue a credit of $50.00 labor for the replacement of a universal joint from the affected lots (see Section IV). Part Credit and a surface freight allowance will be given upon return of the affected part(s).” 

This makes this a low-cost service bulletin for owners to comply with. 

 

 

Know your FAR/AIM and check with your mechanic before starting any work. Always get instruction from an A&P prior to attempting preventive maintenance tasks.

Jacqueline Shipe grew up in an aviation home; her dad was a flight instructor. She soloed at age 16 and went on to get her CFII and ATP certificate. Shipe also attended Kentucky Tech and obtained an airframe and powerplant license. She has worked as a mechanic for the airlines and on a variety of General Aviation planes. She’s also logged over 5,000 hours of flight instruction time. Send question or comments to .

Resources
UNIVERSAL JOINT MC0411257
McFarlane Aviation
 
FURTHER READING
McFarlane Service Bulletin SB-9, Revision A
 
CessnaFlyer.org/forum under “Magazine Extras”

Washington, DC — The General Aviation Manufacturers Association (GAMA) today published the first quarter 2018 aircraft shipment report. The overall delivery of airplanes and rotorcraft rose compared to the same quarter of 2017, but with some mixed performance within the types.

“We are pleased to see the industry is, overall, trending positively,” said GAMA President and CEO Pete Bunce. “Training needs are driving the demands in the rotorcraft segment, while a stabilizing used market, overall global economic growth and aviation innovation are driving the other segment increases. We expect the introduction of new products to drive future growth, which underscores just how important it is for the U.S. Congress to pass a long-term FAA Reauthorization bill and the executive branch to carefully implement trade policies, to avoid adversely affecting industry growth in future quarters — something our member companies conveyed directly to members of Congress this week during GAMA’s annual Hill Day.”

Piston rotorcraft led the first quarter, rising from 58 to 81 units, a 39.7 percent increase. The turbine rotorcraft segment also grew by seven percent to 138 units delivered. The total rotorcraft billings in the first quarter was $0.67 billion, an increase of 18.3 percent.

Turboprop airplane deliveries provided the best performance in the airplane segment, growing by 12.7 percent. The delivery of business jets increased slightly from 130 to 132 airplanes. The piston airplane segment declined by three units, from 203 in first quarter 2017 to 200 in this year.

Airplanes

2017

2018

Change

Piston Airplanes

203

200

-1.5%

Turboprops

102

115

+12.7%

Business Jets

130

132

+1.5%

Total Airplanes

435

447

+2.8%

Total Airplane Billings

$3.71B

$3.83B

+3.3%

 

Rotorcraft

2017

2018

Change

Piston Rotorcraft

58

81

+39.7%

Turbine Rotorcraft

129

138

+7.0%

Total Rotorcraft

187

219

+17.1%

Total Rotorcraft Billings

$0.57B

$0.67B

+18.3%

 

Wednesday, 16 May 2018 14:53

AOPA World Mastercard Rewards Pilots

AOPA and Commerce Bank have come together to offer an exclusive AOPA credit card.

 

The card offers 4 percent cash back1 for select AOPA purchases; 3 percent cash back1 for all purchases at select AOPA partners including Aircraft Spruce & Specialty Co., Aero-Space Reports, Jeppesen®, Sirius XM® Aviation, PilotWorkshops, and Sporty’s® Pilot Shop; 2 percent cash back1 for fixed-based operator (FBO) purchases, aviation and auto fuel costs, ride sharing and taxi costs; and 1 percent cash back1 for all other purchases*. Cash back1 is applied as a statement credit. Cardholders also enjoy the many benefits the World Mastercard® provides, including added convenience with travel services, concierge services, and exclusive golf privileges as well as protection of personal information and prompt assistance in emergencies with Mastercard ID Theft ProtectionTM, extended warranty, price protection, zero liability, and Mastercard Global Emergency Services.

“We are excited to join with AOPA in offering a customized credit card—the pilot’s card—as a way to show their support for the organization, active pilots, and aviation enthusiasts,” said Chad Doza, senior vice president of Commerce Bank. “We are committed to providing customized payment solutions to businesses and organizations in our communities, and we look forward to a rewarding relationship with AOPA.”

The customized card program shows an appreciation for AOPA cardholders and their enthusiasm for aviation. Presented with timely, personalized opportunities to save, the credit card serves to deepen their relationship with AOPA. The card also supports aviators’ interest in and passion for aviation, thereby helping to make their everyday purchases easier and more enjoyable, and providing rewards that matter to them. 

Speaking about the new card, AOPA President Mark Baker said, “Working with Commerce Bank, we have developed the best rewards credit card available to pilots. With a competitive cash back program focused on aviation-related products and services, this new card will allow pilots to save more of their hard-earned money and spend it on what they love—flying.”

The card will be available through the AOPA website. The AOPA credit card is accepted anywhere Mastercard® is accepted.

*Certain points and purchases restrictions apply, see full Rewards Terms and Conditions for full details at AOPA.org/creditcard.

1 Rewards points can be redeemed for Cash Back or other items provided through AOPA Pilot Rewards. A Cash Back redemption is applied as a statement credit. The statement credit will reduce your balance but you are still required to make at least your minimum payment. A minimum of 2,500 points is needed to redeem for Cash Back. Values for non-cash back redemption items such as merchandise, gift cards, and travel may vary.